Review: Private Tube Tara White’s Vagina

We haven’t had a male sex toy to review for a while so this is a kind of refreshment.

But let’s not waste time with unnecessary words and let’s get to the matter.

Today, I’ll be reviewing a Private Tube Penis Masturbator whose inside textures resemble Tara White’s vagina.

The toy was sent to us by Betty’s Toy Box in an exchange for an honest review.

Here’s a quick recap of the review, if you don’t feel like reading the whole thing.

For those of you who don’t know who Tara White is – Tara is a Czech porn star, 33 years old. I didn’t know who she was but Google is my friend, and yours too if you want to read more about Tara.

Box

When I first saw the box, I was stunned by its size. It’s not that I did not expect a bigger piece of the toy but on that first impression, the box was BIG. 

Just to put it into the perspective, I took the ruler and measured it. The box was almost 11 inches (28cm) high and 3.7 inches (9.4) wide and 3.7 inches long.

In the box were the toy, instruction pamphlet, lube, and renewal powder sachets.

Material

The outside tube is made of PP plastic, which is a hard plastic material. 

Inside tube – sleeve is made from TPR – thermoplastic rubber. The sleeve is very soft to touch and has that rubbery feel to it. 

Unfortunately, TPR is a material of questionable quality since it’s a porous material. 

The toy can never be fully cleaned and sterilized since the material has tiny, microscopic holes on the surface. Those holes gather and hold on to various bacteria and there is NO way to clean them out.

Toys made from TPR will never last as long as the silicone toys do and should be replaced at the first sign of wear, dark spots or if they start to feel greasy. 

Also, TPR toys should not be shared between partners.

Sadly, masturbation sleeves made of non-porous materials are hard to find and are often very expensive.  For example, see this one.

So, if you’re a regular Joe like I am and can not afford 200$ sex toys, I would say go for it. 

However, clean it thoroughly, dry it thoroughly, take care of it as much as you can and at first signs of wear, dark spots, or greasiness – get rid of it.

Shape and size

The outside tube resembles the shape of a flashlight, narrow at the top and wider at the bottom. Both top and bottom have a screwable flat top. Will get to that a bit later.

The outside tube (with the top) is also pretty big in size – 10.2 Inches (26cm). I could not resist comparing it with a ‘’household’’ item so I took a small BIC lighter to compare. 

BEEP BOOP BOP. 

By my calculations, 11 small BIC lighters STACKED on top of each other are the same in size as the tube with the top.

Instinctively, I grabbed the tube at the point where it gets wider. It sits nicely in my hand and it’s a real handful.

The bottom, where the entrance is, measures 3.5 inches (8.5cm). 

The whole toy, the outside tube and the sleeve, weigh 7.6 oz (0.22kg).

Using it

Now about the most interesting part.

Since it was the first time I’m using it, I decided to follow the instructions to a T (if that’s the saying).

So the first step says unscrew the bottom, bigger top and remove the inner plastic tube. Which I did. 

The inner plastic tube is nothing more than an 8 inch (20cm) long plastic tube that helps the sleeve’s shape to remain the same after production and during storage and transport.

Ok, back to the instruction’s pamphlet. 

I was holding the toy in one hand and with another trying to unfold the pamphlet. Multitasking at its best.

The second step was to clean and warm the toy. Ok. 

I took the sleeve out of the tube and submerged it in the warm water in the sink. Left it there for 5 minutes. 

The next step was to take it out and either air dry it or wipe it dry with a clean cloth. I left it to air dry since I didn’t want to shove a towel in its tight canal.

By the time it was air-dried, it was cold again. The next time I used the toy, I tried to dry it with a towel, however, showing it in that small whole took me some time and the toy got cold again. 

So the instructions were misleading regarding warming up the toy, however, the ‘’cold’’ toy wasn’t repelling – I even liked the colder sensation on my hard and warm cock.

Step 3 said ‘’Lube it up!’’ 

I took our lube and pumped twice generously into the toy and once in my hand. As you can probably imagine, everything was lubed as it could be. 

Lube was dripping everywhere, even on the couch, good thing Leja was not at home. 

I stroked my cock with that tiny amount of lube and proceeded to insert it inside. That action was effortless.

A quick note on the type of lubricant – the ONLY type of lubricants that are recommended to use with the toy is water-based lubricants. Other lubricants can damage the material.

Once inside, the feeling was pretty good – I liked it. Very soft, and considering the amount of lube I used, very smooth. 

I did dislike the amount of pressure at first but you can fix that easily by unscrewing the smaller, top lid a bit. You can also increase the pressure by screwing the same lid.

And as I wrote, I actually liked the fact that the toy was on the colder side. 

I continued stroking my cock, up and down. I felt the inside bumps and ridges, which I also liked. Combined with the right amount of pressure and speed, it was a winner. I came soon after.

Cleaning

The cleaning process is easy and it lasts no more than 5 minutes. Again, I took the sleeve out and submerged in the warm water, rinsing cum and lube from the inside.

Didn’t use detergent or extra hot water since it says it will damage the toy.

After cleaning it, I left it outside to dry completely. Before putting it away, I dusted both the inside and outside of the toy with the renewal powder they gave with the toy. As they say, it’s a good thing to do.

I have to stress that cleaning it before use is crucial due to the nature of the material and the fact that you should rinse that renewal powder off the toy.

Finale

The big closing words. 

Should you get the toy? Yes and no.

Allow me to explain.

If you’re looking for a sturdy, well-made male masturbator, this toy is an obvious choice.

The outside casing is rigid and the whole toy looks imposing. A definite bonus is the ability to control the pressure and the quality of the inside texture – in some cheaper masturbators that texture is there, however, you can’t feel it on your cock.

However, if you never tried a male masturbator at all, I’d suggest you go with a cheaper, more affordable option (this masturbator costs 76$, lowered from 96$), like this one.

Why? Sleeve material-wise, you are going to get the same or very similar thing, and you’ll get a general idea of how masturbators are and how they work. And from there you can decide if you want to invest more money into a better toy like this one.

I’ll say it one more time – please know that TPR is not the safest material there is but it’s what a bigger majority of masturbators are made from. Should you get one, take care of it and discard it once it goes bad.

That is potentially another reason why you should go with the cheaper option. You can discard it sooner and get a new, fresh one – and eventually spending the same amount of money.

If you decide to go for it, don’t forget to use code SPICES10 to get an additional 10% discount.